1 Before using your ir on for the first time, please remove all the packaging material.
2 When you turn on the iron for the first time it might emit an odor for the first ten
minutes. This is because the materials used in making the iron ar e heating up. The
odor is safe and should not re-occur after the initial heating.
3 Fill water carefully into the water tank without going over “Max” line. Make sur e the
Water Inlet Door is closed to avoid spilling while in use.
4 Plug in the iron into any 120V AC polarized
electrical outlet. The LED Indicator Light
on the handle will light up.
5 Set the desired fabric/temperatur e by turning
the Fabric/T emperature Selector Dial.
6 The LED Indicator Light on the handle will become green once the selected
temperature is r eached. If you wish to change the temperature, the LED Indicator
Light will change to amber to show that the iron is either heating up or cooling down.
The LED Indicator Light will turn green again when the ir on reaches the selected
temperature.
7 T urn the Variable Steam Control Lever to select high or low steam setting.
Select “ ” on the steam control for dry ir oning. Y ou can now star t ironing.
8 Use the Steam Burst Button to remove stubborn wrinkles. Allow an interval of 3
seconds between each burst. Overuse of the steam burst may cause water spitting or
weak steam performance.
9 The Steam Burst feature also works in the vertical position. This is especially useful to
remove wrinkles fr om hanging clothes, delicate garments and other fabrics. Hold the
iron in the upright position several inches away fr om the article.
10 Use the Spray Button to dampen the fabric to tackle tough wrinkles, if necessary .
11 The anti-drip feature is built in to this ir on. It prevents water spitting when the
temperature is too low .
12 Steam cannot be produced if the soleplate is not hot enough. It may r esult in water
spitting or leaking from the soleplate. The anti-drip featur e reduces water dripping and
leaking when ironing at low temperatur es.
13 This iron is equipped with an electr onic auto-off feature that switches the iron off if
it has been idle for 15 minutes in the upright position and after 30 seconds in the
sideways or flat positions.
14 The Indicator Light will flash in red on the handle when the ir on is in auto-off mode. T o
turn the iron back on, just gently r ock the iron back and forth several times until the
LED Indicator Light is re-illuminated. The ir on might have to warm up for a minute if the
auto-off feature was activated for an extended time.
15 Fill the water tank to the “MAX” level. Do not overfill.
16 Stand the iron on its heel, standing up on a pr otected surface and plug into the
electrical outlet.
17 Set the Fabric/T emperature Selector Dial to “•••” setting. W ait until the light stops
flashing. The iron is now on the pr eset temperature.
18 Hold the iron horizontally over the sink. T urn and hold the Steam Control Lever all the
way to the right to the SELF CLEAN position.
19 Move the iron back and forth. Boiling water and steam will now be ejected from the
holes in the soleplate. Use caution when doing this as the water and the steam are hot
enough to cause burns.
20 Repeat step 19 until the impurities and scale are washed away .
21 Empty any excess water from the tank. Don’t touch the hot surfaces, water , or steam
because injury may occur .
22 T urn the steam control to “ ”.
23 Place the iron in upright position and let it cool down.
24 Read all garment care labels befor e you start ironing. Y ou can also test the
temperature of the ir on on a hem or an inside seam.
25 Iron similar fabrics together and in sequence of synthetic fibers nylon, silk/wool,
polyester , and cotton/linen. This will reduce the need to adjust the temperatur e
frequently .
TECHNICAL SPECIFICA TIONS: 120 V olts, 60 Hz., 1500 Watts
1 Stainless Steel Soleplate
2 Water Inlet Door
3 Steam Burst Button
4 LED Indicator Light
5 Spray Nozzle
6 V ariable Steam Control/Self-Clean
7 Spray Button
8 W ater Level W indow
9 Fabric/T emperature Selector Dial
10 Pivot Cord
11 Anti-Drip Function (not shown)
26 Always turn the Variable Steam Contr ol Lever to “ ” after you have emptied the
water tank.
27 Allow the iron to cool down befor e putting it away .
28 Place the iron in the upright position r esting on its heel, during heating up, cooling
down and storage.
29 Avoid any sharp material contacting the soleplate.
30 Every two weeks, clean the exterior of the iron with a damp cloth and wipe dry .
31 If you use spray starch, wipe the soleplate occasionally with a soft, damp cloth to
prevent deposit build-up.
32 If the iron hasn’t been used in a few weeks, hold the ir on horizontally and allow
steaming for 2 minutes before ir oning.
33 Unplug the iron fr om the electrical outlet before pouring water into the ir on.
34 Always empty the water in the iron after each use.
35 Never iron or steam clothes while they ar e being worn.
36 Be very careful when filling the ir on with water . Injuries may occur if the hot metal
parts, hot water or steam are contacted.
Th is a pp lia nc e has a p ola ri zed pl ug (o ne bl ad e is wi de r th an t he o th er).
As a s af et y fe at ur e, th is pl ug w il l fit i nt o a po lar ize d ou tl et o nl y on e way.
If t he p lu g do es n ot fit f u ll y in to t he ou t le t, rev ers e th e pl ug. I f it s ti ll
do es n ot fi t, co nt ac t a qua li fie d el ect r ici an. D o not a t te mp t to de fe at t his
safety feature.
The iron doesn’t
An odor is being
emitted from the
new iron or small
particles are
coming out
Iron doesn’t
Water dr oplets
coming from
steam vents.
Iron should be plugged into a 120V AC electric outlet only .
Make sure the plug is secur ely in the socket.
T emperature setting might be too low .
T ry turning to a higher setting.
Auto-off feature is activated.
This is normal.
Follow the instructions for first-time use and allow iron to steam
through 2-3 fillings and pr ess the Steam Burst Button occasionally
to eliminate small white particles.
Water tank may be empty or water level is very low . Add water .
Make sure the fabric/temperatur e setting and the Variable Steam
Control Lever ar e correctly set. For maximum steam, set to
“ ” on the Variable Steam Contr ol Lever and the temperature
setting should be set on “•••”.
Variable Steam Contr ol Lever is set on “ ”.
The soleplate is not hot enough and the anti-drip feature switches off
the steam. Always allow the iron to r each the selected temperature
with the Variable Steam Contr ol Lever setting at “ ”. For more
steam, turn temperature dial to a higher setting and the steam
control to “ ”.
If the temperature setting and steam contr ol settings are corr ect and
there is no steam, gently move the ir on left or right a couple of times.
Move the Variable Steam Contr ol Lever from “ ” to “ ” a few times.
Variable Steam Contr ol Lever may be set in “self clean” position.
Align the lever to the “ ” to “ ” steam setting.
Iron may not be hot enough. Set temperatur e to “•••” position.
Always allow iron sufficient time to heat up befor e activating the
variable steam control.
The Steam Burst may have been overused. Allow more time
between each burst.
EURO-PRO Operating LLC warrants this product to be free from material defects and workmanship for a period of one (1) year from the date of purchase when utilized for normal household use, subject to the following conditions, exclusions and exceptions. The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alteration to the product or any of its parts, which have been performed by a repair person not authorized by EURO-PRO Operating LLC. If your appliance fails to operate properly while in use under normal household conditions within the warranty period, you may return the complete appliance and accessories with proof of purchase and date, freight prepaid. For customer service
support, call 1-800-798-7398 or visit our website at www.sharkclean.com .
If the appliance is found by EURO-PRO Operating LLC to be defective, in EURO-PRO Operating LLC’s sole discretion, we will repair or replace it free of charge. Proof of purchase date and check made payable to EURO-PRO Operating LLC in the amount of $12.95 to cover the cost of return shipping and handling must be included. This warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/or conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the specific obligations expressly assumed by it under the terms of this Limited Warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential damages to anyone of any nature whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you. This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province. *IMPORTANT : Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and to attach a tag to item before packing including your name, complete address and phone number with a note giving purchase information, model number and what you believe is the problem with the item. We recommend you insure the package (as damage in shipping is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore the specifications contained herein are subject to change without notice.
CAUTION! TO PREVENT ELECTRIC SHOCK OR OTHER INJURY , before filling the iron with
water , make sure that the plug is r emoved from the outlet.
WARNING: Never fill the iron with fabric conditioner , starches or any other solution, as
these will damage the steam mechanism. Do not use contaminated water .
CAUTION! TO AVOID FIRE, never leave ir on unattended while it is plugged in.
CAUTION! TO PREVENT ELECTRIC SHOCK, never use the iron in a location wher e it can
fall or be pulled into water or another liquid. If the iron falls into water or other liquid,
